As a key component that bears axial loads (commonly used in equipment such as machine tool spindles and motor rotors), maintenance and care should focus on reducing wear, maintaining lubrication, and avoiding overload.
I. Daily Inspection and Monitoring
Operational Status Observation
Regularly observe the bearing's operating noise (normally, there should be no noticeable abnormal noise. Any "rustling" or "clicking" sound may indicate wear or foreign matter intrusion), vibration (measure using a vibration detector. If the amplitude exceeds the specified value, shut down the equipment for inspection), and temperature (generally, the temperature rise should not exceed 40°C above ambient temperature. If the temperature continues to rise, it may indicate poor lubrication or overtightening).
Axial Clearance Inspection
After shutting down the machine, use a feeler gauge or specialized tool to measure the bearing's axial clearance (requirements vary depending on the equipment, but generally, the range should be 0.03–0.1 mm). If the clearance is too large, the thrust surface is severely worn. If the clearance is too small, overtightening may be causing heat and requires prompt adjustment.
Seal Inspection
Check the seals (such as oil seals and sealing rings) on the bearing end caps for signs of grease leakage, dust, or moisture intrusion. Seal failure can lead to grease contamination or loss, requiring immediate replacement.
II. Cleaning and Lubrication Maintenance
Regular Cleaning
Non-disassembly Cleaning: Clean the bearing exterior and surrounding area. Use a brush to remove surface dust and oil to prevent impurities from entering through gaps.
Disassembly Cleaning (for periodic overhauls): After removing the bearing, soak it in kerosene or a specialized bearing cleaner to remove old grease and residual impurities. Dry it with a soft cloth. (Do not use a high-pressure water jet to directly rinse the bearing to avoid damaging the raceway.) If scratches or pits are found on the raceway or thrust surface, evaluate whether the bearing needs to be replaced.
Grease Selection and Filling
Grease selection should be based on operating conditions:
For high-speed journal thrust bearings (such as machine tool spindles), a low-viscosity, shear-resistant lithium-based grease is recommended.
For high-temperature environments (such as kiln equipment), a high-temperature, extreme-pressure grease is recommended.
For humid environments, a water-resistant grease is recommended.
Filling Method: After cleaning, evenly apply grease between the bearing raceways, thrust surfaces, and retainer, filling 1/2–2/3 of the bearing's internal space (too much will cause stirring and heating, while too little will result in insufficient lubrication). After assembly, run the bearing for 1–2 minutes to evenly distribute the grease.

III. Installation and Operating Environment Control
Avoid Overload and Shock
Journal thrust bearings primarily bear axial loads and should avoid excessive radial loads or frequent shock (such as transient overloads during equipment startup). Impact damage can be reduced by installing overload protection devices (such as a torque limiter) or optimizing the startup procedure (such as slow acceleration).
Environmental Protection
Preventing Contaminants: In dusty and humid environments (such as mining machinery and water treatment equipment), install dust covers or protective shields on bearings and regularly inspect the seals.
Temperature Control: Avoid prolonged operation of bearings in high-temperature environments (exceeding the grease's upper temperature limit). If necessary, install cooling devices (such as water cooling jackets) to prevent grease failure and metal overheating and aging.
IV. Troubleshooting and Replacement
Common Troubleshooting
If a slight abnormal noise is heard but the temperature is normal, shut down the machine to check the lubrication condition, refill or replace the grease, and then conduct a test run.
If the temperature continues to rise and is accompanied by vibration, it may be due to raceway wear or misalignment. Disassemble and inspect, and if severe, replace the bearing.
If the grease is emulsified (white paste), this indicates water intrusion. Clean the bearing, replace with water-resistant grease, and repair the seals.
Contact Us
Call us on:+8613738301065+8613738366645
Email: ZBBearings@outlook.com
Address: Units 1-1 and 3-1, Building 12, Yongxing Nanyuan Small and Micro Enterprise Startup Park, Binhai 2nd Road, Yongxing Subdistrict, Longwan District, Wenzhou City, Zhejiang Province.

