Hey there! As a supplier of tilting pad thrust bearings, I've seen firsthand how crucial the cleanliness of the lubricant is for these bearings. In this blog, I'm gonna break down what's needed to keep that lubricant clean and why it matters so much to the performance and lifespan of our Tilting Pad Thrust Bearing.
Why Clean Lubricant is a Big Deal
Let's start with the basics. Lubricant in tilting pad thrust bearings does a couple of super important jobs. First off, it reduces friction between the moving parts. When the bearing is in operation, the pads tilt and slide against each other, and without proper lubrication, that friction can generate a ton of heat. Too much heat can lead to all sorts of problems, like wear and tear on the pads, and in the worst - case scenario, it can cause the bearing to fail completely.
Secondly, the lubricant acts as a coolant. It carries away the heat generated during operation, keeping the bearing at a safe temperature. But if the lubricant is dirty, it can't do these jobs effectively. Contaminants in the lubricant can act like little sandpaper particles, scratching the surfaces of the pads and reducing their efficiency.
Particle Size and Concentration
One of the key requirements for lubricant cleanliness is controlling the size and concentration of particles in the lubricant. Most manufacturers have specific standards for this. For example, we usually look at particles in the range of 4 - 6 micrometers and larger.
The concentration of these particles is measured in terms of the number of particles per milliliter of lubricant. A cleaner lubricant will have fewer particles. Industry standards often use the ISO 4406 code to classify the cleanliness of the lubricant. This code gives a three - number rating, which indicates the number of particles of different sizes in the lubricant.
For tilting pad thrust bearings, we generally recommend a relatively high - level of cleanliness. A typical target might be an ISO 4406 code of 18/16/13. This means that there are fewer than 1300 particles per milliliter in the size range of 4 - 6 micrometers, fewer than 400 particles per milliliter in the 6 - 14 micrometer range, and fewer than 64 particles per milliliter in the 14 - 21 micrometer range.
If the lubricant has a higher particle concentration than this, it can cause accelerated wear on the bearing pads. The particles can get trapped between the pads and the rotating surface, causing abrasion and reducing the bearing's ability to tilt and adjust properly.
Contaminant Types
It's not just about the size and number of particles; the type of contaminants also matters. There are a few common types of contaminants that can find their way into the lubricant.
Solid Particles
These can come from a variety of sources. Rust and scale can form inside the lubricant reservoir or piping if there's moisture present. Metal shavings can be generated from normal wear and tear on the bearing or other components in the system. Dust and dirt can also enter the lubricant if the system isn't properly sealed.
Solid particles are particularly problematic because they can cause mechanical damage to the bearing surfaces. They can create small scratches and grooves, which can lead to increased friction and heat generation.
Water
Water in the lubricant is another big no - no. It can cause corrosion of the bearing components, especially the metal parts. Water can also react with the lubricant itself, breaking down its chemical properties and reducing its effectiveness.
Even a small amount of water can have a significant impact on the lubricant's performance. For example, water can cause foaming, which reduces the lubricant's ability to form a proper film between the moving parts.
Air
Air bubbles in the lubricant can also be a problem. When air is mixed with the lubricant, it can cause cavitation. Cavitation occurs when the pressure in the lubricant drops below the vapor pressure of the lubricant, causing the formation of vapor bubbles. When these bubbles collapse, they can create high - pressure shock waves that can damage the bearing surfaces.
Filtration Systems
To meet the cleanliness requirements, a good filtration system is essential. There are different types of filters that can be used in a tilting pad thrust bearing lubrication system.
Full - Flow Filters
These filters are designed to filter all of the lubricant that passes through the system. They are usually the first line of defense against contaminants. Full - flow filters can remove larger particles, typically in the range of 10 - 20 micrometers. However, they may not be able to remove very small particles effectively.


By - Pass Filters
By - pass filters, on the other hand, only filter a small portion of the lubricant at a time. These filters are often used to remove smaller particles, down to the sub - micrometer range. They work by slowly filtering the lubricant over time, gradually reducing the overall particle concentration in the system.
A combination of full - flow and by - pass filters is often the best approach. This way, you can remove both large and small particles, ensuring that the lubricant meets the required cleanliness standards.
Regular Monitoring
Even with a good filtration system in place, it's important to regularly monitor the cleanliness of the lubricant. This can be done through oil analysis. Oil analysis involves taking a sample of the lubricant and testing it in a laboratory.
The tests can measure a variety of properties, including the particle size and concentration, the presence of water and other contaminants, and the chemical properties of the lubricant. By regularly analyzing the lubricant, you can detect any changes in its cleanliness and take corrective action before it causes problems for the bearing.
Impact on Bearing Performance
Maintaining the proper cleanliness of the lubricant has a direct impact on the performance of the tilting pad thrust bearing. A clean lubricant allows the bearing to operate more smoothly. The pads can tilt and adjust freely, reducing friction and heat generation. This, in turn, extends the lifespan of the bearing.
On the other hand, a dirty lubricant can lead to premature failure of the bearing. Increased wear on the pads can cause the bearing to lose its ability to support the axial load properly. This can result in vibrations, noise, and ultimately, a breakdown of the bearing.
How We Can Help
As a supplier of Pedestal Pad Thrust Bearing and Pad Thrust Bearing, we understand the importance of lubricant cleanliness. We can provide you with detailed guidelines on the cleanliness requirements for our bearings.
We also offer support in setting up the right filtration systems for your lubrication system. Our team of experts can help you choose the appropriate filters and ensure that they are installed and maintained correctly.
If you're in the market for tilting pad thrust bearings or need advice on lubricant cleanliness, don't hesitate to reach out. We're here to help you get the most out of your bearings and keep your equipment running smoothly. Contact us to start a discussion about your specific needs and how we can assist you.
References
- ISO 4406:2017, Hydraulic fluid power - Fluids - Method for coding the level of contamination by solid particles.
- Machinery's Handbook, 31st edition, Industrial Press Inc.
- Tribology Handbook, Second Edition, CRC Press.
